|
Tungsten Probe Tips with Nickel
Shank
Stock Code : J410
Custom probe tip design with nickel tube shank and tungsten
tip. Tip radius is 0.5µm with a 13° taper angle for maximum lifetime
|
Tungsten Probe Tips
Stock Code : J411
Custom all-W design, with tip radius of 0.3µm and a 10°
taper angle for maximum lifetime.
|
In-situ Probe Tips
Stock Code : J412
In-situ probe tips - custom tungsten tip w/ stainless steel
shank for use with AutoProbe™ 300, in-situ probe
tip exchange systems, 0.5µm and a 8°-10° taper angle.
|
|
Xtreme Access ½" Tungsten Probe Tips
Stock Code : J450
Custom all-W design, with tip radius
of 0.3µm and a 10° taper angle for maximum lifetime.
|
Autoprobe 250 Probe Tips
Stock Code : J413
Custom all-W design, with tip radius
of 0.3µm and a 10° taper angle for maximum lifetime. Compatible w/ ShortCut™
system for direct conversion to TEM grid
|
Xtreme Access Probe Point Holder
Stock Code : J455
Xtreme Access probe tip holder for use with ½"
tungsten probe tip, PT-0001.04.01 only.
(Comes with a storage vial.)
|
|
Copper
Lift-out Grids
Stock Code : J420
Custom copper lift-out grids
specifically designed for in-situ lift-out. These grids include multiple indexed
mounting locations with both vertical bar and "V" shaped attachment
surfaces.
|
Moly Lift-out Grids
Stock Code : J421
Custom moly
lift-out grids specifically designed for in-situ lift-out. These grids
include multiple indexed mounting locations with both vertical bar and
"V" shaped attachment surfaces.
|
Copper 5 Post Lift-out Grids
Stock Code : J422
5 post grid - Custom copper lift-out grids specifically designed for in-situ
lift-out. These grids include multiple indexed mounting locations, all with
vertical bar attachment surfaces. Now
with lower profile sides for easier access to outermost posts.
|
|
Copper 4 Post Lift-out Grids
Stock Code : J423
4 post grid - Custom copper lift-out grids specifically designed for in-situ lift-out.
These grids include multiple indexed mounting locations, two with vertical
bar attachment surfaces and two with “V’ shaped alignment surfaces. Sides have lower profile for easier access
to outermost posts.
|
Frontside Thinning Copper Coupons
Stock Code : J440
Custom copper, frontside thinning TEM sample grid coupon designed specifically for
use in the Short-Cut™ tool. The center portion is a standard 3mm grid into
which the sample loaded needle is swaged and cut.
|
Backside
Thinning Copper Coupons
Stock Code : J441
Custom copper, backside thinning TEM
sample grid coupon designed specifically for use in the Short-Cut™ tool. The
center portion is a standard 3mm grid into which the sample loaded needle is swaged
and cut.
|
|
Grid
Storage Box
Stock Code : J430
Storage box for 100 standard 3mm TEM grids. Complete with base, lid and clips.
|
End
Effector Mo Type2 (curved)
Stock Code : J451
(Pack of 12)
Moly curved END EFFECTOR designed for low attack angle
manipulation and lift-out. The shank in curved to permit low angle approach
and solid attachment beneath the sample plane without collision with the
surrounding matrix.
|
End
Effector Cu Type2 (curved)
Stock Code : J452
(Pack of 12)
Copper curved END EFFECTOR
designed for low attack angle manipulation and lift-out. The shank in curved
to permit low angle approach and solid attachment beneath the sample plane
without collision with the surrounding matrix.
|
|
End
Effector Mo Type3 (straight)
Stock Code : J453
(Pack of 12)
Moly straight END EFFECTOR for Xtreme
Access probe shaft
|
End
Effector Cu Type3 (straight)
Stock Code : J454
(Pack of 12)
Copper straight END EFFECTOR
for Xtreme Access probe shaft
|
TEM Grid Holder, Stainless
Steel
Stock Code : J400
Post base TEM grid holder. Stainless steel and very
slightly magnetic, can affect imaging in UHS
mode. Short post - standard 1/8" dia x
0.15" long.
|
|
TEM Grid Holder, Non-Magnetic
Stock Code : J401
Post base TEM grid holder, non-magnetic. Short post -
standard 1/8" dia x 0.15" long.
|
TEM Sample & Grid Holder, Stainless Steel
Stock Code : J402
TEM grid holder w/ stations for 2 TEM grids & 2 sample pucks. Stainless steel -
very slightly magnetic. Long post - standard 1/8" dia
x 0.32" long. [Includes 2 sample pucks]
|
TEM Sample & Grid Holder, Non-Magnetic
Stock Code : J403
TEM grid holder w/ stations for 2 TEM grids & 2 sample pucks. Non-magnetic.
Long post - standard 1/8" dia x 0.32"
long. [Includes 2 sample pucks]
|
|
Single TEM
Grid Sample Holder
Stock Code : J404
Holds a standard FIB
lift-out specimen on a grid
|
Single TEM
Grid Sample Holder Base
Stock Code : J405
Holds the single TEM grid holder under a stereomicroscope and
permits viewing from two angles without changing focus
|
Agar Scientific - Home |